Category Archives: CM

Concrete Mender on the Busan Metro Line 4

The Busan Transportation Corporation uses Roadware 10 Minute Concrete Mender to repair the roll-way of Busan Metro Line 4 in South Korea. Metro Line 4 is a rubber-tired line with 14 stations and runs driverless with pneumatic tires on a 6.7 mile (10.8km) concrete track. Concrete Mender is used to structurally repair the cross joints in the track approximately every ten meters.

Concrete Mender is the right product for the job because it has a long service life and cures in about 10 minutes. This allows for minimal down time and keeps the Busan Metro Line 4 running on time with minimal service interruption.

Repair crews of a very limited repair window, The train operates approximately 20 hours per day from 5am to 1am the next day. That leaves a minimal amount of time for maintenance and repair operations. Crews have to be efficient and productive. The fast cure and rapid strength gain of 10 Minute Concrete Mender is well suited for these mission critical applications.

 

 

Having a smoother roll-way saves wear and tear on the rubber tires and reduces operating costs.  Roadware 10 Minute Concrete Mender will keep the Busan Metro Line 4 running smooth and efficiently for years to come.

Edward Cheon of Concrete Doctor in Seoul on the concrete roll way at Busan Metro Line 4.

 

Roadware 10 Minute Concrete Mender is a self-injecting structural polyurethane for the permanent repair of commercial floors, decks, slabs and surfaces. The exclusive Microdoweling™ action in Concrete Mender allows it to migrate past bond lines, restore aggregate interlock and make long lasting repairs.

Crack in concrete floor ready for repair with Roadware 10 Minute Concrete Mender.

 

Click here to request more information of find a local Roadware distributor.

Roadware 10 Minute Concrete Mender™ comes in 50ml or 600ml cartridges or two and ten gallon bulk kits.

 

Warehouse floors can be repaired and open for traffic in about 10 minutes after application.

 

Click here to request more information or find a local Roadware distributor.

Crack Repair Under VCT or Laminate Flooring

Use Concrete Mender™ to repair  cracks, joints and curling slabs under VCT or tile floors. The permanent performance and 10 minute cure turns this 2 day job into a one day (or one night) job. Keep business running with minimal down time.

Repairing control or contraction joints under VCT.
Repairing contraction joints under VCT.

For spalled or failed control joints that are reflecting through the tile and the slabs are not curled, clean out the joints with a dust collecting diamond grinder.

Control or contraction joints repaired with 10 Minute Concrete Mender™ under VCT.
Control or contraction joints repaired with 10 Minute Concrete Mender™ under VCT.

Repair the control joints with Roadware 10 Minute Concrete Mender™, grind the surface flush and replace the tile.

 

For curled and buckled slabs, a major retailer specifies this heavy duty solution. This is the ultimate fix it once and fix it forever repair.

crack-repair-concrete-mender-vct-flooring_03

Step 1: Remove VCT, Ceramic, or vinyl floor coverings.

 

crack-repair-concrete-mender-vct-flooring_06

Step 2: Saw cut parallel lines to the crack at a depth of no less than 1.5 inches. Ideally 30% of the slab depth.

 

crack-repair-concrete-mender-vct-flooring_08

Step 3: Chip out the concrete between the saw cuts. Clean the surface well with a wire brush and vacuum.

 

crack-repair-concrete-mender-vct-flooring_10

Step 4: Add Roadware 10 Minute Concrete Mender and Sand to the finished grade. Also use Concrete Mender to repair the underlaying crack. See Concrete Mender™ Bulk Application Instructions.

 

crack-repair-concrete-mender-vct-flooring_13

Step 5: Replace the floor treatment and open to store traffic.